Quick-Ohm, Components, Heatmanagement, High tech ceramic Sitemap Data Privacy Policy Impessum German

Heat Management


range table

Moduls for Thermo-CYCLER-Applications

M-Series Modules

In 2002 this modified module line was introduced, giving an extraordinary reliability. The cycling stability was achieved by improvements of the diffusion barriers of the thermoelectric materials as well as the mechanical design.

The standard test for cycling used to be 40°C/90°C in 5-6 minutes turned out to be too long lasting for the new modules. A lifetime test until failure would have taken several years. Therefore a new test was created to face the higher demands of cycling applications at a reasonable testing period.

In Fig. 1 an overview over the new test cycles is given with temperature cycles up to 120°C in 20 sec. Fig. 2 shows the experimental setup with an alternator for power supply.

The higher standard of the new modules is shown in the failure criteria. A module is failing the test when the inner AC-resistance is lowered by 5% of its initial value. The module is still working after the failure only showing a slightly worse performance.
 
Diagramm Peltierelement
Fig. 1: Optimized test procedure for Thermo-CYCLER Applications
Diagramm Peltierelement

Fig. 2: Experimental Setup for Cycling-tests

 

MM-Series-Modules

The Modules of the MM-Line were developed for applications with a still higher demand for cycling stability such as “Burn-In”-Tests for CPU QA or PCR-Cycler.
The MM-Series is a further development on the M-Series and has specifications for higher cycling stability.
The mechanical design was optimized to take up the forces induced by thermal expansion

 

Table 1 shows the cycling stabilities of the M-series and MM-series Modules.

Table 1: Cycling Stabilities of the different Modules series

Line Test -20 /+120 °C Test +40 /+90 °C
unsymmetrical Cycles
Test +40/+90 °C
symmetrical Cycles
M-Series 10-15 x 10³ 200-300 x 10³ 800-1000 x 10³
MM-Series 20-30 x 10³ 400-600 x 10³ 1500-2000 x 10³
 
 
 
PELTIER ELEMENTS
one-stage cycling modules
super cycling
Cycling application modules
Bezeichnung Konfektionierung Umax
V
Qcmax
W
Imax
A
DTmax
K
Warme
Seite
Kalte
Seite
 
QC-31-1.0-3.9 MM 3.6 8.9 3.9 72 15 mm x  15mm 15 mm x  15mm
QC-32-2.0-9.0 MM 3.6 21 9 72 25.4 mm x  28.4mm 25.4 mm x  25.4mm
QC-32-2.0-15.0 MM 3.7 34 15 71 25.4 mm x  28.4mm 25.4 mm x  25.4mm
QC-70-2.5-15.5 MM 8 73 15.5 71 36.4 mm x  54.4?mm 36.4 mm x  50.2mm
QC-70-2.5-24.0 MM 8 110 24 71 36.4 mm x  54.4mm 36,4 mm x  50.2mm
QC-71-1.0-3.9 MM 8.2 20.4 3.9 72 22.4 mm x  22.4mm 22.4 mm x  22.4mm
QC-71-1.4-6.0 MM 8.2 30 6 71 30 mm x  30mm 30 mm x  30mm
QC-71-1.4-8.5 MM 8.2 40 8.5 71 30 mm x  34mm 30 mm x  30mm
QC-71-1.4-9.0 MM 8.2 44 9 71 30 mm x  30mm 30 mm x  30mm
QC-71-1.6-15.0 MM 8.2 67 15 71 29.8 mm x  33.8mm 29.2 mm x  29.2mm
QC-69-1.4-9.0 MM 8.9 48 9 71 35?mm x  40mm 35?mm x  35mm
QC-127-1.0-3.9 MM 14.6 36.6 3.9 72 30 mm x  30mm 30 mm x  30mm
QC-127-1.4-6.0 MM 14.6 53 6 71 40 mm x  40mm 40 mm x  40mm
QC-127-1.4-8.5 MM 14.6 71 8.5 71 40 mm x  40mm 40 mm x  40mm
QC-127-1.6-15.0 MM 14.6 115 15 71 40 mm x  40mm 40 mm x  40mm
QC-144-1.2-8.0 MM 16.6 78 8 71 16.8 mm x  76.7mm 16.2 mm x  72.4mm
QC-161-1.6-15.0 MM 18.5 148 15 71 40 mm x  40mm 40 mm x  40mm
QC-241-1.6-15.0 MM 27.7 225 15 71 50 mm x  54mm 50 mm x  50mm